NEWS CENTER
任何設備除了正確使用外，都是需要維護和保養的，用于設備上的滑環也不列外，正確的使用可以使滑環的壽命延長，并且有必要定期進行維護和保養，那么如何正確保養滑環呢?
下面以鐵精密給大家講解：
一、滑環拆卸清洗流程：
1、關閉所有通過滑環的電流和信號
2、拆卸支撐板上的螺釘，讓定子框架可以旋轉;
3、按照箭頭方向退出滑環殼體;
4、將“滑環清洗劑”對準環道進行噴射清洗;旋轉定子框架，可 以清洗導電環道
5、讓清洗后的滑環揮發10—20 分鐘。
注意事項：
1、應該是專業維護人員拆卸清洗滑環，一般人員請勿試圖拆卸滑環;
2、除非特別臟污，一般清洗不需要拆卸PCB電路板，只需要旋轉定子框架就可以清洗全部導電環道;
3、禁止將刷針從PCB電路板上面取出。因為每一根刷針的彈性壓力都經過準確調整，你拆卸后不可能讓它還原。
二、滑環的潤滑裝配流程
1、待清洗劑充分揮發以后，將“滑環潤滑劑”均勻的噴灑到導電環表面;旋轉定子框架，可以讓潤滑劑噴灑得更加均勻;
2、安裝橡膠密封圈，安裝滑環外殼;固定支撐板螺釘。
三、滑環清洗劑的選擇
1、清洗劑的要求：滑環清洗劑應該能夠溶解輕油形成的油垢，溶解電弧形成的積碳 和脂肪類污物等，有較強的揮發性能。
清洗劑不能對金屬有腐蝕作用，不能使橡膠或塑料老化或脆裂。建議使用專門“滑環”清洗噴霧劑”。
四、滑環潤滑劑的選擇
1、滑環潤滑劑應該有較小的表面張力，能夠均勻的分布在導電環道 表面;
2、滑環潤滑劑能夠減少環道與刷針接觸表面的摩擦阻力、減少磨損， 防止環道和刷針的氧化、腐蝕。
3、滑環潤滑劑的粘度應該對溫度變化不敏(min)感，在-40°C的時候粘度沒有明顯增加，在80°C 的時候不揮發。
如何正確保養滑環就分享以上，希望能夠幫到大家，有任何不明白的可以直接咨詢我們工程師
In addition to the correct use of any equipment, it is necessary to maintain and maintain the sliding ring. The sliding ring used in the equipment is not listed. The correct use can extend the life of the sliding ring, and it is necessary to maintain and maintain it regularly. How to properly maintain the sliding ring?
The following is an iron precision to explain to everyone:
First, the sliding ring disassembly cleaning process:
1, turn off all current and signal through the sliding ring
2, remove the screw on the support plate, so that the stator frame can rotate;
3, exit the sliding ring shell in the direction of the arrow;
4, the "sliding ring cleaning agent" aimed at the ring for jet cleaning; Rotation of stator frame to fully clean conductive loops
5, let the cleaning of the sliding ring volatilize for 10-20 minutes.
Notes:
1, should be the professional maintenance personnel disassemble clean sliding ring, general personnel do not attempt to dismantle sliding ring;
2, unless it is particularly dirty, general cleaning does not require the removal of PCB circuit boards, only need to rotate the stator frame to clean all conductive loops;
3, prohibit the brush needle from the PCB circuit board. Because the elastic pressure of each brush needle is precisely adjusted, it is impossible to restore it when you remove it.
Second, lubrication assembly process of sliding ring
1, after the cleaning agent is fully volatilized, the "sliding ring lubricant" is evenly sprayed on the surface of the conductive ring; Rotating the stator frame allows the lubricant to be sprayed more evenly;
2, install rubber sealing ring, install sliding ring shell; Fixed support plate screws.
III. Selection of Slip Ring Cleaner
1, cleaning agent requirements: sliding ring cleaning agent should be able to dissolve light oil formation of tartar, dissolved arc formation of carbon and fatty pollutants, such as strong volatilization.
The cleaning agent can not corrode the metal and can not age or brittle the rubber or plastic. It is recommended to use a special "sliding ring" cleaning spray.
IV. Selection of Sliding Ring Lubricants
1, sliding ring lubricant should have a small surface tension, can be evenly distributed on the surface of the conductive ring;
2, sliding ring lubricant can reduce the friction resistance of the ring and brush needle contact surface, reduce wear, prevent the oxidation and corrosion of the ring and brush needle.
3, the viscosity of the sliding ring lubricant should be insensitive to temperature changes. The viscosity does not increase significantly at -40 °C and does not evaporate at 80 °C.
How to properly maintain the sliding ring to share the above, I hope to help you, if you do not understand can directly consult our engineers